How to prepare wxGTK distribution ================================= 0. Introduction --------------- This note explains what should be done, step by step, to prepare the packages for a wxGTK distribution. Note that the same instructions should be used for the other Unix-based ports including wxMotif, wxX11 and wxBase. 1. Preparing the sources ------------------------ a) Do a fresh checkout using the command cvs -d :pserver:anoncvs@cvs.wxwindows.org:/packs/cvsroots/wxwindows co wxGTK NB: if you realize later that some needed files were not checked out by this command, please modify CVSROOT/modules to include the missing files so that it works for the next release! You also need the samples, demos and contrib directories, so change to wxWindows directory created by the first cvs command and do "cvs up -d" for each of them. b) Create a build directory under wxWindows, e.g. I use "gtk-release", "cd" to it and run configure: the options don't really matter, you can use something like ../configure --no-recursion to make it run a bit faster. c) Then type "make -j1 dist bzip-dist-only". This should create the following files; wxGTK-${version}.tar.bz2 wxGTK-demos-${version}.tar.bz2 wxGTK-samples-${version}.tar.bz2 wxGTK-${version}.tar.gz wxGTK-demos-${version}.tar.gz wxGTK-samples-${version}.tar.gz where version is something like 2.3.2. Note 1: "-j1" is needed now because make dist target is broken and doesn't allow parallelizing, if your make is aliased to "make -j4" (like mine), it simply won't work. Note 2: there are also dist-only and bzip-dist targets, the "-only" suffix means to just create the archive supposing that the files themselves are already under _dist_dir/wxGTK-${version} where "make dist" creates them 2. Building the RPMs -------------------- Note that we didn't check if the library actually could be built -- this is because it is done during this step, during the RPM generation. If, for whatever reason, you don't build the RPMs, you must have checked previously that the library could be built -- nothing worse than a release which doesn't even compile! The rest of this section applies to a system with RPM installed (Redhat in my case). a) Setting up the RPM tree: you should have the RPM tree set up properly before doing anything else. If you are going to build the RPMs as root, you already have one under /usr/src/redhat and can just build there. Otherwise you may do it (without root rights) in any directory RPM_ROOT. RPM_ROOT should have the following subdirectories: BUILD, RPMS, SOURCES, SPECS and SRPMS. RPMS should contain i386, i686 and noarch. You should also create the file ~/.rpmmacros containing at least a line like this: "%_topdir /biton/zeitlin/rpm" (replace the directory with $RPM_ROOT, of course) In either case, put the file wxGTK-${version}.tar.bz2 in SOURCES subdirectory and wxGTK.spec in SPECS one (hint: you can just link them from there -- like this you won't forget to update them after redoing "make dist"). b) Start RPM build by going to RPM_ROOT directory and typing "rpm -ba SPECS/wxGTK.spec". It may be a good idea to append "2>&1 | tee wxGTK.out" (or "|& tee" if you're using the one true shell ;-) as it might be not easy to detect errors in the verbose rpm output if anything goes wrong. Then wait (and pray that nothing goes wrong because if anything does you'll have to restart from the very beginning because rpm doesn't allow to short circuit the package generation). If everything goes well, the following files are produced: SRPMS/wxGTK-${version}-1.src.rpm RPMS/i386/wxGTK-${version}-1.i386.rpm RPMS/i386/wxGTK-devel-${version}-1.i386.rpm RPMS/i386/wxGTK-gl-${version}-1.i386.rpm RPMS/i386/wxGTK-static-${version}-1.i386.rpm Use "rpm -ba --with gtk2" to build GTK+2 version of wxGTK and use "rpm -ba --with gtk2 --with unicode" to build GTK+2 Unicode build. Note: you may want to set the environment variable SMP to 3 or 4 on an SMP machine to speed up the build (it uses "make -j$SMP" if the variable is set) c) Test the resulting RPMs: install them using "rpm -i" (or "rpm -U) as usual and try to build some samples using makefile.unx ("make -f makefile.unx") so that they use wx-config in the PATH and not from the build tree 3. Building the DEBs -------------------- [Ron is doing this] 4. Uploading the files ---------------------- All 11 files should be uploaded (via FTP) to several locations. a) incoming.sourceforge.net, go to project admin page on sf.net and choose add/edit releases for more details b) ftp://biolpc22.york.ac.uk/pub (Julian has the password) 5. Announcing the release ------------------------- a) FreshMeat: - http://freshmeat.net/projects/wxwindowsgtk/ - username and password are "wxgtk" for logging in - hit "new release" at the top - follow the step by step b) wx-announce mailing list: mailto:wx-announce@lists.wxwindows.org [where is the announcement text? TODO] c) update www.wxwindows.org d) GNOME (very effective, stays on front page for days): - http://www.gnome.org/applist - Search for wxWindows - Update the version number - Ignore the error message e) MacNN: - http://www.macnn.com - Contact or Contribute or something f) MacRumors: - http://www.macrumors.com - Contact or Contribute or something g) Apple Developers Connection: mailto: adcnews@apple.com h) LinuxDevices.com: Interesting for wxUniversal. i) The Python mailing list: